On receiving end debug will start showing IKE packet exchange and tunnel will come up. IKE Receiver: device udp/localized/v successfully opened IKE Receiver: device udp/localized/2/4500 successfully opened You should see successful log messages this time.
Removing PAT rules will impact production trafficĪfter removing PAT you need to clear xlate again and re-enable IKE on outside interface. Port forward on Cisco ASA 5505 (8.4) not working I have now given up the gui as I finally found a serial port for my computer - the gui/ASDM really sucks Anyway, today I first reset everything to factory default, then configured via cli.
UDP PAT from any:/4500 to outside:/4500 flags ri idle 0:05:50 timeout 0:00:30Ĭlearing xlate did not fix the issue so I had to remove PAT rule. Just wanted to ask on how to open up a range of ports on the cisco asa I would like to open up UDP ports 10000-20000 I have found a way and the code is below: code:1 access-list outsideaccessin extended permit udp any host public ip range 10000 20000 static (inside, outside) interface private ip public ip netmask 255.255.255. I’ve grepped xlate for 4500 and found that some private IP was PATed to outside IP on port UPD/4500 causing issues with IKE. IKE Receiver: device udp/localized/v6/2/500 successfully openedīased on output something was holding on to port UDP/4500. IKE Receiver: device udp/localized/2/500 successfully opened IKE Receiver: IO port exists on intf 2(outside), checking for delayed delete timer IKE Receiver: IO port create request for intf 2(outside) Since error pointed out the issue is with IKE I’ve tried disabling and re-enabling IKE on outside interface (receiving end) and received the following error message.ĮRROR: Failed to open “udp/localized/2/4500”ĮRROR: Error opening IKE port 4500 on Interface outside Initiating side would display a message stating that none of IKE configured settings matched remote peer and receiving side (where IP changed) had no messages at all. After updating all the proper VPN setting with new IP address a working tunnel would not establish for some unknown reason. Static translate 8.8.8.8/3456 to 8.8.8.This issue had me going for a bit because it started happening on a working production unit after public IP address changed.
Username XXX password XXX encrypted privilege 15 No threat-detection statistics tcp-intercept Snmp-server enable traps snmp authentication linkup linkdown coldstart warmstartĬrypto ipsec security-association pmtu-aging infiniteĭhcpd address 10.10.10.230-10.10.10.240 inside Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absoluteĭynamic-access-policy-record DfltAccessPolicy Nat (inside,outside) source static SVR interface service udp-9191 udp-9191 In other words, allow email to go out port 587 from any computer on the inside. I need to send email from the inside to outside over port 587. Nat (inside,outside) source static SVR interface service udp-9090 udp-9090 2 Comments 1 Solution 2360 Views Last Modified. Nat (inside,outside) source static SVR interface service udp-8080 udp-8080 Nat (inside,outside) source static SVR interface service tcp-9191 tcp-9191 Confirm the ACL Manager NOTE: With the Cisco ASA 5505 there are no fixup protocols to configure however, common issues noted with many Cisco ASA models relate to their use of fixup protocols. Nat (inside,outside) source static SVR interface service tcp-9090 tcp-9090 Nat (inside,outside) source static SVR interface service tcp-8080 tcp-8080 Icmp unreachable rate-limit 1 burst-size 1 Here is what I have so far ASA Version 9.0(1)Īccess-list 100 extended permit icmp any any echo-replyĪccess-list 100 extended permit tcp any object SVR eq 8080Īccess-list 100 extended permit tcp any object SVR eq 9090Īccess-list 100 extended permit tcp any object SVR eq 9191Īccess-list 100 extended permit udp any object SVR eq 8080Īccess-list 100 extended permit udp any object SVR eq 9090Īccess-list 100 extended permit udp any object SVR eq 9191 What I am trying to do is forward 3 ports using TCP & UDP protocols on my ASA5505 running OS 9.0 to a server on the inside. Any and all information is greatly appreciated. I've been beating my head against this for a while now and I've tried all links I could find that were even the least bit relevant to my situation.